Licensed and Insured Drying Contractors
Every contractor we refer is an independent local business that carries its own license and insurance. Many train to the IICRC S500 standard for water damage drying; ask your tech about their certifications.
24/7 Drying Line Open
Structural Drying in Loma, CO
The water is gone, the carpet feels fine and the wall looks normal, but the framing behind it can still be holding a surprising amount of moisture. Getting a structure truly dry is a numbers game, measured with meters and humidity readings rather than fingertips.
One call to our referral line puts you in touch with a licensed, insured independent drying contractor serving Loma. Your tech sets dehumidifiers and air movers to a plan, logs readings every day and gives you a written estimate up front.
- Drying goals set against unaffected material
- Readings recorded on every monitoring visit
- Licensed, insured independent drying contractors
- In-place drying where it saves materials
While the drying runs
- Keep all equipment running around the clock
- Hold windows shut unless the tech says to open them
- Keep the heat or AC at the setting your tech gives
- Do not move air movers or dehumidifiers
Why callers use this line
Why Choose Our Specialized Structural Drying Network in Loma, CO
Proper drying is part science and part routine: read the air, read the materials, adjust, and repeat until the numbers line up. This is what the independent drying techs in our network bring.
Written Estimates Tied to the Drying Plan
The estimate lists equipment counts, expected drying days and monitoring visits, so the bill is easy to follow. Daily logs back up each line for the adjuster.
Fast Response From Nearby Techs
Starting early often means drywall, baseboard and floors can be dried in place rather than replaced. Our dispatcher confirms a real arrival window with a nearby tech while you are on the line.
Meters, Thermal Cameras and Psychrometric Tools
Drying techs carry thermo-hygrometers to read temperature, relative humidity and grains per pound, plus pin and pinless meters for wood and drywall. Equipment ranges from LGR and desiccant dehumidifiers to wall cavity injection kits and hardwood floor drying mats.
What the meters show
Why Dry to the Touch Does Not Mean Dry
Here is a call the dispatch desk gets every week: a leak was fixed, the wall looks fine, but a tech puts a meter on it and it reads high. Drywall paint dries on the surface first and seals moisture inside the gypsum core and the stud behind it. Seal it up or push furniture against it, and mold can grow out of sight for weeks.
The drying target comes from what techs call the dry standard: readings taken on unaffected drywall, framing or flooring elsewhere in the house. When the wet wall reads within range of that dry standard, it is dry; until then, the equipment keeps running.
Wood floors make the point just as clearly. With a slow leak under a dishwasher, the underside of the boards swells and the edges lift, which is called cupping. Sand it flat too early and it crowns once it dries. Drying mats and steady monitoring can often bring the boards back flat.
The short version: dry, warm air draws water out of materials, dehumidifiers remove it from the air, and air movers sweep the surface so evaporation keeps going.
- Relative humidity is how full the air is relative to what it can hold at that temperature
- Grains per pound (GPP) measures how much water is actually in the air, regardless of temperature
- Moisture moves from high vapor pressure in wet materials toward lower pressure in drier air
- Dew point tells the tech where condensation could form on cold slabs and outside walls
Where drying equipment goes
What a Drying Job Actually Covers
Techs start by rating the job Class 1 through 4, which sets how much dehumidification and airflow it takes.
Moisture Mapping and the Dry Standard
With meters and thermal imaging, the tech outlines the wet zone and reads unaffected material to set a target. Those readings get marked on a sketch so every visit checks the same spots.
Rating the Loss by Class
Class 1 is a small area with little absorption; Class 4 means dense materials like hardwood, plaster or concrete that hold water deep. The class drives how many dehumidifiers and air movers go in.
- Class 2: a full room, with water wicking a short way up the walls
- Class 3: saturation from overhead, soaking ceiling, walls and floor
Choosing the Right Dehumidifier
LGR dehumidifiers drive the air drier than a standard unit, which is what most residential jobs need. Desiccant units work better in cold spaces and on dense materials like hardwood and concrete.
Wall Cavity Injection Drying
Instead of tearing out drywall, the tech can drill small holes at the base of the wall and push dry air into the cavity. It works well for clean water caught early, and the holes hide under the trim.
Saving Cupped Hardwood
Mats seal against the wood and draw moisture up through the boards and the subfloor below. Wood readings are checked against dry flooring in another room until they line up.
Daily Logs and Drying Charts
Every visit the tech records temperature, relative humidity and GPP inside, outside and at the dehumidifier exhaust, plus material readings. That chart shows the adjuster the job is drying as planned, and when it is done.
How a drying job runs
How Structural Drying Works, Step by Step
Call the Drying Dispatch Line
Tell the dispatcher what kind of water it was, how long ago it happened and which materials got wet. We route the call to the closest independent drying tech and give you an arrival window.
Tech Arrives and Takes First Readings
The tech reads the air inside and outside, then maps moisture through the walls, floors and ceilings. Readings on dry material in another room set the target.
Drying Plan and Written Estimate
The tech assigns the evaporation class, decides what can be dried in place and what has to come out, and sizes the equipment. You get a written, line-itemed estimate before the machines start.
Monitoring, Resolution and Sign-Off
The tech checks readings every day or so, moves or removes equipment as areas dry, and logs every visit. When every point matches the dry standard, the equipment comes out and you sign off with the full drying log in hand.
What people told us after
Drying Stories From Our Callers
After an upstairs toilet leak, the wall below looked totally normal by the next day. I called the referral line mostly for peace of mind, and the contractor they connected me with put a meter on it and it was soaked behind the paint. The crew blew dry air into the wall through small holes behind the baseboard and showed me the numbers falling each visit.
A slow leak under our dishwasher made the kitchen oak floor cup. I was ready to replace the whole floor. My tech set up drying mats and compared the boards to dry flooring in the dining room each visit. Most of it settled back down, and they were upfront about the few boards that still needed attention.
The machines were loud and I wanted to shut them off at night. My tech explained that turning them off lets the moisture rebound and costs you a day of drying. We kept them running and the job wrapped up in about four days.
Common drying questions
Straight Answers About Structural Drying
How long does structural drying take?
Most clean-water jobs dry in about three to five days, but dense materials like hardwood, plaster and concrete can take longer. The evaporation class, the weather and how quickly drying started all change the timeline. Your tech can update the estimate as the daily readings come in.
Why do the drying machines have to run 24 hours a day?
The equipment keeps the air drier than the wet materials, which is what pulls moisture out of them. Stopping the machines lets humidity rise again, and the materials stop giving up water or even reabsorb it.
Can I turn the drying equipment off at night?
It is best not to. Turning the equipment off overnight usually adds days to the job. If noise is a real problem, ask your tech whether a unit can be repositioned; do not move or switch off machines on your own.
How do they know when the structure is completely dry?
Readings on the affected materials are checked against the same material in a dry room, which is the dry standard. Once every point on the moisture log reaches that range, the job is considered dry. You get the daily log as proof for your records and your adjuster.
How much electricity do drying machines use?
Running dehumidifiers and air movers day and night will add to your electric bill for those days. Plenty of insurance carriers reimburse the extra electricity on covered claims, so ask your adjuster and save the bills. Your tech will spread the load across circuits so nothing trips.
Where techs respond
Structural Drying Techs Around Loma
The independent drying contractors we refer work homes, condos and small commercial spaces across Loma.
We also hear from people whose space was already dried but still smells musty or shows moisture. A second set of readings from an independent tech can tell you where things stand.
- Drywall and framing
- Cupped wood floors
- Wet subfloors
- Plaster walls
- Wet ceilings
Talk to a drying dispatcher now
Tell us what got wet and when, and we will connect you with an independent drying tech near Loma.
Call +1-877-637-9008Still Reading Wet? Get It Measured
In a few minutes with a meter, a tech can tell you whether the structure is actually dry. One call connects you with an independent drying contractor nearby.
